|
Product Details:
|
| Product Name: | Dissolved Oxygen Analyzer | Model: | OPD79 |
|---|---|---|---|
| Range: | 0.00~20.00 Mg/L | Principle: | Fluorescence Method |
| Pressure: | 3bar | Accuracy: | 0.1mg/L |
| Communication: | RS485 MODBUS RTU | Protection Grade: | IP68(sensor) |
| Operating Temperature: | 0.0~50.0℃ | Material: | Enhanced ABS |
| High Light: | Dissolved Oxygen Sensor ABS,Water Station Dissolved Oxygen Sensor,0.1mg/L Dissolved Oxygen Analyzers |
||
China Manufacturer Do probe Dissolved Oxygen Sensor for Water station
Compared with traditional polarographic electrodes, the fluorescence dissolved oxygen sensor developed and produced by Delfino is more suitable for real-time dissolved oxygen monitoring. Its shell is ABS sturdy and durable, the measurement results are accurate, and the maintenance is very easy. At the same time, it is also a digital electrode with built-in RS485 communication and supports Modbus protocol.
Specification of Dissolved Oxygen sensor
|
Model |
OPD79 |
| Measuring Range |
Oxygen content: 0.00~20.00 mg/L |
| Resolution | 0.01mg/L 1% |
| Accuracy | 0.1 mg/L 1% |
| Response Time | T90 less than 60s |
| Temperature Compensation | Automatic, built-in temperature unit |
| Calibration Method | Zero position/slope/deviation |
| Work Pressure | 0~3Bar |
| Operating Temperature | 0.0~50.0℃ |
| Material | ABS |
| Dimensions | Diameter: 35mm Total length: 260mm |
| Installation Size |
1"NPT at both ends of the installation thread; |
| Protection Grade | IP68 |
| Weight | 170g |
Features of the dissolved oxygen sensor
1. No need to calibrate, meet the requirements of on-site work
2. There is no need to consume oxygen, and it can be accurately measured even when the oxygen concentration is low.
3. With RS458 interface, it supports access to standard industrial control systems.
4. The protection grade is IP68, which can work continuously under water for a long time.
5. Internal storage of calibration data, plug and play on site.
6. No need for polarization, no electrolyte. The service life is 1-2 years, and you can continue to use it after replacing the fluorescent cap.
Application
It is widely used in urban sewage treatment, industrial wastewater treatment, surface water monitoring, aquaculture and other industries.
It can be matched with DUC2-DO single-parameter controller or connected with MCC100 five-parameter controller to realize the water quality monitoring of a set of water stations.
| Model | DUC2-DO-H-A | |
| Software Version | DRFN DO Analysis software V1.0 | |
| Sensor Input | Compatible with all DRFN's DO Digital Sensors | |
| Display Range | DO Concentration | DO concentration 0-50mg/L (or ppm), unit can be switched |
| Saturation | 0-400% | |
| TEMP | -10～500℃ /14~932℉ | |
| Atmospheric Pressure | 30-120kpa | |
| Resolution | DO Concentration | 0.01 mg/L(or ppm) |
| Saturation | 1% | |
| TEMP | 0.1℃/ 0.1℉ | |
| Salinity Compensation Range | Input range 0.0001-99999ppt | |
| Relay Control | 2 settable SPST relays with a maximum load of 3A/250VAC | |
| Analog Current Output | 2 settable 0/4~20mA current outputs, max load 1000Ω | |
| Communication Method | RS485 interface MODBUS RTU support JSON text data format |
|
| Display Screen | 128*64 LCD, adjustable backlight mode, adjustable display rate | |
| Configuration Information | Power off protection, parameters are retained indefinitely | |
| Time/Data Record | Record 14000 historical data Record interval can be set between 1~999 minutes |
|
| Maintenance Records | Last 100 | |
| Operating Temperature | 0～60℃,RH<95% ( no condensation) | |
| Storage Temperature | -20～70℃, RH<55% ( no condensation, precision instruments) | |
| Shell Material | Enhanced ABS | |
| Protection Grade | IP66 | |
| Dimension | 144*144*120 mm | |
| Mounting Method | Wall mounting, pipe clamping, panel (hole size 138*138 mm) | |
| Electrical Interface | The back end reserved 3 M12*1.5 Gram head, line diameter 3~6.5 mm | |
| Power Supply | 100～240VAC | |
| Power Consumption | About 7W | |
| Weight | About 800g | |
If you are interested in dissolved oxygen sensors, please contact us.
FAQ:
1. Is your company a manufacturer?
We are a manufacturer. We have our own R&D team and production workshop to ensure the quality and quantity of products.
2. How is the price of the product determined?
The price of the product is ordered according to the purchase quantity. If your purchase is large and will have a long-term cooperation, then we will give you a special price.
Contact Person: Ms. Yuki Fu
Tel: +8615716217387
