logo
Home News

company news about Daruifuno Launches DEC890 0.2W Digital Conductivity Sensor for Solar Powered Remote Water Monitoring

Certification
China Suzhou Delfino Environmental Technology Co., Ltd. certification
China Suzhou Delfino Environmental Technology Co., Ltd. certification
I'm Online Chat Now
Company News
Daruifuno Launches DEC890 0.2W Digital Conductivity Sensor for Solar Powered Remote Water Monitoring
Latest company news about Daruifuno Launches DEC890 0.2W Digital Conductivity Sensor for Solar Powered Remote Water Monitoring

Suzhou, China — Daruifuno has introduced the DEC890 digital conductivity sensor, a graphite two-electrode instrument engineered for continuous online water monitoring where mains power is unavailable or expensive. The sensor operates on a DC 9~36V wide voltage input and draws only about 0.2W, a power budget that allows it to run from a small solar panel, a 12V or 24V battery bank, or the same low-capacity DC bus that feeds a remote data logger.

A Sensor Designed Around the Power Budget

Remote water monitoring projects rarely fail because of the measurement technology. They fail because the power system cannot support the instruments. A conductivity probe that needs a dedicated power supply forces integrators to add converters, larger batteries and bigger solar arrays, and every extra component becomes a maintenance item in the field.

The DEC890 removes that constraint. Two parallel graphite plates are immersed in the water, a driving voltage is applied across them, and the conductivity of the solution is calculated from the current flowing between the plates. Graphite is used instead of metal because it substantially reduces polarization, the electrochemical effect that causes metallic electrodes to drift during long immersion. The result is a stable signal with an accuracy of ±1% of the selected measuring range and resolution down to 0.01uS/cm.

Key specifications at a glance

Measuring principle Graphite two-electrode cell
Measuring ranges 0~20uS/cm, 20~200uS/cm, 200~2000uS/cm, 2~10mS/cm
Resolution 0.01uS/cm, 0.1uS/cm, 1uS/cm
Accuracy ±1% of measuring range
Power supply DC 9~36V, about 0.2W
Communication RS485 MODBUS-RTU, address 17, 9600bps, 8N1
Protection IP68, 0~1 Bar, 0~50°C
Housing Stainless steel 316 + POM, 37mm diameter, 261mm length

Built for Stations That Are Hard to Reach

Solar powered surface water stations, battery backed wells, hilltop reservoirs, irrigation canals and decentralized sewage treatment plants all share the same profile: no mains power, infrequent maintenance visits and an expectation that the data will keep flowing through the rainy season. The DEC890 is specified for exactly these sites.

  • Wide voltage tolerance: the DC 9~36V input absorbs the voltage sag of a battery under load and the swing of an unregulated solar bus.
  • Isolated communication: the power supply and the RS485 line are electrically isolated, preventing ground loops when several digital sensors share one long bus.
  • IP68 sealing: the stainless steel 316 and POM body can be installed submerged in tanks, channels and wells instead of only in a bypass line.
  • Field-replaceable measuring head: a fouled or damaged electrode cell is exchanged as a module, keeping the housing, cable and electronics in service.

Calibration Without a Laboratory

Offset calibration, factor calibration, two-point calibration and multi-point calibration up to five points are supported. In routine service, two samples of known conductivity are enough to establish the offset and factor values. When the measuring head is replaced or the range changes, standards of 84uS/cm, 146uS/cm, 1413uS/cm and 12880uS/cm can be measured in sequence, with each reference value written directly to its Modbus register. A dedicated reset register returns the sensor to factory calibration in a single command, which simplifies site handover and auditing.

Availability

The DEC890 is available with a standard 10-meter shielded cable and M16 connector; customized cable lengths are offered for deep wells and long pipeline runs. Both ends of the 37mm body are machined with 1-inch NPT threads, so the same sensor fits side wall brackets, top flanges, pipeline tees, submerged mounts and flow-through housings. Buyers can specify the measuring range, cable length and connector type at the time of order, and the factory pre-configures the Modbus address and communication parameters before shipment.

For technical documentation, pricing and sample requests, contact the Daruifuno sales team and quote model DEC890 together with the required measuring range.

Pub Time : 2026-11-20 16:42:01 >> News list
Contact Details
Suzhou Delfino Environmental Technology Co., Ltd.

Contact Person: Ms. Yuki Fu

Tel: +8615716217387

Send your inquiry directly to us (0 / 3000)